Siding hooks that hold
a full sheet.
Set 16 steel hooks at the panel's required bottom-edge height. The sheet's bottom edge sits at the right height and the wall takes the weight while your two-person crew positions and fastens it off.
- Creates consistent support across the panel's bottom edge
- 16 steel support points in the kit, not one scrap board or two clamps
- Tap it off and move up a course. Nothing to unscrew, and the fastener ends up behind the finished panel
Free shipping to all 50 states · Ships in 1 to 2 business days · 30-day returns
Watch the complete installation sequence.
See the official 2:25 EZPanl Instructional Video before reviewing the written steps.
Improvised panel support is where the day falls apart.
Ask any siding crew. A heavy full sheet that will not stay put, on a wall, at the right height, while you try to fasten it. This is the job EZpanl was built for.
It slips and drifts
Lining a full sheet up with the studs while keeping it level and stopping it from sliding is a fight, even with the whole crew on it.
A screwed ledger adds steps
A screwed ledger adds setup and removal steps. Crews fasten the board, support the panel, remove the board, and prepare for the next course.
Holding is not installing
Hands pinned under a panel are hands that are not positioning, checking the reveal, or fastening. The first panel goes on crooked and the wall follows.
Keep it up off the ground
Keep the panel supported above the work surface while the crew positions it to the manufacturer's required clearance.
Establish the height. Support the panel. Fasten it off.
Install the hooks only as directed in the current EZpanl instructions. Rest the panel on the installed hooks while a minimum two-person crew positions and fastens it to the panel manufacturer's requirements.
Attach the hooks
Use a level or laser to establish the panel's required bottom-edge height. Install each hook so its support foot meets that reference, following the current EZpanl instructions.
Set the panel
With a minimum two-person crew, place the panel so its bottom edge rests in the hooks.
Adjust with ease
Use the EZhandle as directed to adjust the panel to the required reveal.
Purpose-built for full panels. Not a gauge, not a scrap board.
Most siding gauges are made for lap plank and clamp to the course below. EZpanl is purpose-built to support full panels while the crew positions and fastens.
| EZpanl Kit | Screwed ledger / cleat | Panel clamp | |
|---|---|---|---|
| Attachment method | One fastener per hook into the wall* | Screwed or nailed to the wall | Temporary clamp attachment per manufacturer instructions |
| Support points per kit | 16 support hooks | 1 board | 2 clamps |
| Cost per support point | ~$12 ($199 for 16) | Scrap + crew time, every course | ~$50 ($99.99 for a set of two)† |
| Moving to the next course | Tap off, move up | Unscrew, patch, rebuild | Unclamp, move |
| Exposed holes to patch after | Nail sits behind the panel | Row of exposed holes | None |
* EZpanl supports the panel during positioning and fastening. Always follow the siding manufacturer's flashing, water-resistive-barrier, fastening, clearance, and installation requirements. † PacTool listed its SA907 panel clamp at $99.99 for a set of two in retail listings checked July 2026. Per-support figures are each listed price divided by the pieces in that package.
Purpose-built for full rigid panel siding.
EZpanl supports full rigid panel siding while a minimum two-person crew positions and fastens it. The panel's bottom edge rests on a row of support hooks nailed to the wall, so the wall takes the weight while the crew positions and fastens.
Confirm your specific panel, substrate, and wall conditions against the current EZpanl instructions and your siding manufacturer's requirements.
Compare it against your own setup.
Compare the purchase price with your own crew's current setup and removal process. No labor-savings figure is claimed without a measured job-site study.
support hooks in the kit. Set them along the wall as the current EZpanl instructions direct.
EZpanl
Siding Hook Kit
Includes 16 EZpanl hooks and 1 EZhandle.
- 16 EZpanl hooks made from 11-gauge steel with a bright red powder-coated finish
- 1 EZhandle for adjusting the panel as directed
- Free shipping to all 50 states, 30-day returns
Straight answers to the questions crews actually search.
Written against verified product data and the siding manufacturer's published requirements, so a foreman can check the work.
How do you hold a siding panel in place while you fasten it?
Every support option for rigid panels, compared honestly.
Read the guide How-ToReplacing improvised ledger boards on panel work
Purpose-built support hooks vs the scrap-cleat routine.
Read the guide CompareEZpanl vs cleats vs panel clamps
How each attaches, what each costs, and the labor each one takes.
Read the guideOutfit your crew.
Running a siding crew? Give your crew purpose-built panel support instead of rebuilding scrap ledgers. Volume and dealer pricing available.
Request crew pricing